8 3 8 4 0 A D I A M O N D M A X MAXTOR
Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 6569| 7441| |
Capacity form/unform 3840/ MB Heads 6| 16| |
Seek time / track 10.0/ 1.0 ms Sector/track | 63| |
Controller IDE / ATA3 ENHANCED Precompensation
Cache/Buffer 256 KB MAXCACHE Landing Zone
Data transfer rate 13.420 MB/S int Bytes/Sector 512
16.700 MB/S ext PIO4
Recording method RLL 8/9 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 71
Power: sleep 0.6 W Humidity % 5 95 | 5 95
standby 0.8 W Altitude km -0.061 3.048|
idle 4.5 W Shock g 20 | 150
seek 5.0 W Rotation RPM 5400
read/write 5.3 W Acoustic dBA 36
spin-up W ECC Bit SMART
MTBF h 500000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MAXTOR 85120A/83840A/82560A/81280A DIAMOND JUMPER SETTING
J1 IDE Connector J2 Power
+----------- --------1-++-----------+
| .................... || * * * * |/---------\
| .......... ......... || * * * * * || O O O O |
+----------------------++-----------++---------+
| | | | | | | | |
| | | | | | | | |
J50 Master/Slave ---+ | | | | | | | +-+12V (Yellow)
J48 Cable Select -----+ | | | | | +---+12V Return (Black)
J46 4092 Cyl Limitation-+ | | | +----- +5V Return (Black)
J44 Factory Reserved -----+ | +------- +5V (Red)
J42 Factory Reserved -------+
**********************************************************************
J U M P E R S
**********************************************************************
MAXTOR 85120A/83840A/82560A/81280A DIAMOND JUMPER SETTING
Jumper Setting
==============
+---+---+---+---+---+
|J50|J48|J46|J44|J42|
+-------------------------------------+---+---+---+---+---+
| Master/Slave | | | | | |
| Only Drive in single drive system* | J | | | | |
| Master in a dual drive system* | J | | | | |
| Slave in a dual drive system | O | | | | |
+-------------------------------------+---+---+---+---+---+
| Cable Select | | | | | |
| Disabled* | | O | | | |
| Enabled | | J | | | |
+-------------------------------------+---+---+---+---+---+
| 4092 Cylinder Option | | | | | |
| Disabled* | | | O | | |
| Enabled | | | J | | |
+-------------------------------------+---+---+---+---+---+
| Factory Reserved | | | | O | |
+-------------------------------------+---+---+---+---+---+
| Factory Reserved | | | | | O |
+-------------------------------------+---+---+---+---+---+
J=Jumpered O=Open *=Default
Systems Using Cable Select
--------------------------
Most systems do not use this feature. Unless you are sure that the
system that the Maxtor hard drive is being installed in uses Cables
Select, do not set up the drive with this feature enabled.
Maxtor hard drives support Cable Select - which allows the system
to identify Devuce 0 and Device 1 drives on the interface cable. If
your system manufacturer for specific procedures for installing hard
drives.
On Maxtor DiamondMax hard drives, the Cable Select is enabled by
installing a jumper on J48. When J48 is installed, remove the jumper
from J50.