7 8 1 3 A P MAXTOR
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders | 1579| |
Capacity form/unform 813/ MB Heads | 16| |
Seek time / track / ms Sector/track | 63| |
Controller IDE / ATA2 FAST/ENHA Precompensation
Cache/Buffer KB Landing Zone
Data transfer rate MB/S int Bytes/Sector 512
MB/S ext
Recording method operating | non-operating
-------------+--------------
Supply voltage Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g |
seek W Rotation RPM
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MAXTOR 71050/71626/71260/71084/7813/7541AP QUICK REFERENCE
+---------------------------------------------------------+
| J20****** |
| COMPONENT SIDE ****** |XXI
| |XXN
| |XXT
| |XXE
| |XXR
| |XXF
| |XXA
| |XXC
| |XXE
| |XX
| |XX
| |XX
| | 1
| |XX Power
| |XX
+---------------------------------------------------------+ 1
**********************************************************************
J U M P E R S
**********************************************************************
MAXTOR 71626/71260/71084/7813/7541AP QUICK REFERENCE
Jumper Setting
==============
Jumper Designation
------------------
+---------------- J20
| +------------- J21 RESERVED!
| | +---------- J22 RESERVED!
* * * * * *
* * * * * *
| | +- J25
| +---- J24
+------- J23
+-----------------------+------+------+------+
| | J24 | J23 | J20 |
+-----------------------+------+------+------+
| Cable Select | | | |
| Disabled (default) |OPEN | | |
| Enabled |CLOSED| | |
+-----------------------+------+------+------+
| Write Cache | | | |
| Enabled (default) | |OPEN | |
| Disabled | |CLOSED| |
+-----------------------+------+------+------+
| Master/Slave | | | |
| Only Drive in system | | |CLOSED|(default)
| Master | | |CLOSED|
| Slave | | |OPEN |
+-----------------------+------+------+------+
A spare shunt is shipped between J23 and J24.
NOTE
Jumpers J21 and J22 are factory reserved.
DC Power connector
------------------
pin 1 +12 VDC
pin 2 +12 Volts Return
pin 3 + 5 Volts Return
pin 4 + 5 VDC
**********************************************************************
F E A T U R E S
**********************************************************************
MAXTOR 71626/71260/71084/7813/7541 QUICK REFERENCE
Installation Steps
------------------
Warning
Pre-loaded Software on Drive
This Maxtor hard drive is factory configured with a 112MB partition
containing Max Blast Disk Manager installation software by Ontrack
Systems. Please leave this partition intact until you choose the
appropriate installation option.
As a precautionary measure, Maxtor recommendeds that you download a
copy of the MaxBlast software to a blank diskette even if you choose
an alternate high-level formatting method.
Install a 40-pin ribbon connector. The striped edge of this cable
represents pin 1 and must be oriented towards pin 1 at the drive
connector and at the host connector.
Install a DC power connector...
If AT BIOS supports user programmable parameters, program System BIOS
with one of these default Parameters.
Model Cylinders Heads Sectors Capacity
71262AP 3158 16 63 1,626 MB
71260AP 2632 16 63 1,260 MB
71084AP 2105 16 63 1,084 MB
7813AP 1579 16 63 813 MB
7541AP 1052 16 63 541 MB
If AT
BIOS does not support programmable drive type, choose parameters that
closely match, but do not exceed, the drive's formatted capacity.
The drive is now ready for partitioning and high-level formatting
with any operating system. For example:
Partition the drive using the FDISK command from MS-DOS
version 3.3 of higher.
High level format the drive using the FORMAT command from
MS-DOS version 3.3 or higher.
Secure the drive in a suitable drive bay with 6-32 x 1/4" screws.
NOTE
WPC and Landing Zone BIOS entries do not need a specific number for
proper operation. Maxtor AT interface hard drives will ignore and
override any numbers programmed.
Important - Please Read
-----------------------
This Quick Reference is intendened only for experienced engineers and
technicans. If you are not familar with the procedures described
here, please have a qualified computer technican perform drive
handling and installation.